BS EN ISO 15848-2-2015

收藏

编号:20181011230817561110    类型:共享资源    大小:1.05MB    格式:PDF    上传时间:2018-11-05
  
30
Gold
关 键 词:
BSENISO15848 2015
资源描述:
BSI Standards Publication BS EN ISO 15848-2:2015 Industrial valves — Measurement, test and qualification procedures for fugitive emissions Part 2: Production acceptance test of valves (ISO 15848-2:2015)BS EN ISO 15848-2:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN ISO 15848-2:2015. It supersedes BS EN ISO 15848-2:2006 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PSE/18/1, Industrial valves, steam traps, actuators and safety devices against excessive pressure - Valves - Basic standards. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. © The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 82088 5 ICS 23.060.01 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2015. Amendments issued since publication Date Text affected EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO 15848-2 June 2015 ICS 23.060.01 Supersedes EN ISO 15848-2:2006 English Version Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 2: Production acceptance test of valves (ISO 15848-2:2015) Robinetterie industrielle - Mesurage, essais et modes opératoires de qualification pour émissions fugitives - Partie 2: Essais de réception en production des appareils de robinetterie (ISO 15848-2:2015) Industriearmaturen - Mess-, Prüf- und Qualifikationsverfahren für flüchtige Emissionen - Teil 2: Fertigungsbegleitende Abnahmeprüfung von Armaturen (ISO 15848-2:2015) This European Standard was approved by CEN on 7 February 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15848-2:2015 EBS EN ISO 15848-2:2015 EN ISO 15848-2:2015 (E) 3 Foreword This document (EN ISO 15848-2:2015) has been prepared by Technical Committee ISO/TC 153 “Valves” in collaboration with Technical Committee CEN/TC 69 “Industrial valves” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2015, and conflicting national standards shall be withdrawn at the latest by December 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 15848-2:2006. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 15848-2:2015 has been approved by CEN as EN ISO 15848-2:2015 without any modification. BS EN ISO 15848-2:2015ISO 15848-2:2015(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Preparation of test valves 1 4.1 Valve selection . 1 4.2 Preconditioning 1 4.3 Stem (or shaft) seal adjustment . 2 5 Test conditions . 2 5.1 Test fluid . 2 5.2 Leakage measurement . 2 5.3 Test pressure. 2 5.4 Test temperature . 2 6 Test procedure and evaluation of test results 2 6.1 Measurement of stem (or shaft) seal leakages 2 6.2 Measurement of leakage of body seal(s) 3 7 Marking 3 8 Certification of compliance 3 © ISO 2015 – All rights reserved iii Contents PageBS EN ISO 15848-2:2015ISO 15848-2:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword — Supplementary information. The committee responsible for this document is ISO/TC 153, Valves, Subcommittee SC 1, Design, manufacture, marking and testing. This second edition cancels and replaces the first edition (ISO 15848-2:2006) which has been technically revised. The main changes are the following: — tightness classes (Table 1) are the following: A: 50 ppmv; B: 100 ppmv; C: 200 ppmv — if the reading exceeds the values of the required tightness class according to Table 1 or Table 2, the test is considered as having failed. Then, a corrective action is proposed and agreed with the purchaser or the lot of valves is rejected. ISO 15848 consists of the following parts, under the general title Industrial valves — Measurement, test and qualification procedures for fugitive emissions: — Part 1: Classification system and qualification procedures for type testing of valves — Part 2: Production acceptance test of valvesiv © ISO 2015 – All rights reservedBS EN ISO 15848-2:2015ISO 15848-2:2015(E) Introduction The aim of this part of ISO 15848 is to establish standard practice for the evaluation of production valves, the design of which has been successfully type-tested according to ISO 15848-1.© ISO 2015 – All rights reserved vBS EN ISO 15848-2:2015BS EN ISO 15848-2:2015Industrial valves — Measurement, test and qualification procedures for fugitive emissions — Part 2: Production acceptance test of valves 1 Scope This part of ISO 15848 specifies test procedures for the evaluation of external leakage of valve stems or shafts and body joints of isolating valves and control valves intended for application with volatile air pollutants and hazardous fluids. End connection joints, vacuum application, effects of corrosion, and radiation are excluded from this part of ISO 15848. The production acceptance test is intended for standard production valves where fugitive emissions standards are specified. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 15848-1:2015, Industrial valves — Measurement, test and qualification procedures for fugitive emissions — Part 1: Classification system and qualification procedures for type testing of valves 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 15848-1 and the following apply. 3.1 production acceptance test test carried out on production valves to verify conformance with the requirements of this part of ISO 15848 4 Preparation of test valves 4.1 Valve selection The sampling percentage shall be subject to an agreement between the manufacturer and the purchaser, with a minimum of one valve of the lot, and shall be selected at random from each production lot of valves per valve type, pressure class, and nominal size. 4.2 Preconditioning This part of ISO 15848 is applicable to valves, the design of which has been successfully type-tested according to ISO 15848-1. The selected valves shall have been successfully tested according to the relevant production test standards and the purchaser’s specifications, prior to the acceptance test specified in this part of ISO 15848. INTERNATIONAL ST ANDARD ISO 15848-2:2015(E) © ISO 2015 – All rights reserved 1BS EN ISO 15848-2:2015ISO 15848-2:2015(E) The packing shall be dry before production test. 4.3 Stem (or shaft) seal adjustment Compression of stem (or shaft) seal(s) shall be initially adjusted according to the manufacturer’s instructions. 5 Test conditions 5.1 Test fluid The test fluid shall be helium gas with a minimum purity of 97 % by volume. 5.2 Leakage measurement Leakages shall be measured by sniffing method in accordance with ISO 15848-1:2015, Annex B, and shall be expressed in ppmv. 5.3 Test pressure The test pressure shall be 6 bar (1 bar = 0,1 MPa = 10 5Pa; 1 MPa = 1 N/mm 2 ), unless otherwise agreed by the manufacturer and the purchaser. 5.4 Test temperature The test temperature shall be at room temperature as defined in ISO 15848-1. 6 Test procedure and evaluation of test results 6.1 Measurement of stem (or shaft) seal leakages The procedure for measuring the leakage of stem or shaft seals is as follows. a) Half open the test valve and pressurize to the level specified in 5.3. Measure the stem seal leakage using the sniffing method in accordance with ISO 15848-1:2015, Annex B. b) Then, fully open and close the pressurized test valve five times. c) Half open the test valve after the mechanical cycles and measure the stem seal leakages as in a). d) If the reading exceeds the values of the required tightness class according to Table 1, the test shall be considered as having failed. A corrective action shall be proposed and agreed with the purchaser or the lot of valves shall be rejected. Table 1 — Tightness classes for stem seals Class Measured leakage ppmv Remarks A ≤50 Typically achieved with bellow seals or equivalent stem (shaft) sealing system for quarter turn valves B ≤100 Typically achieved with PTFE based packings or elas- tomeric seals C ≤200 Typically achieved with flexible graphite-based packings NOTE Measured by sniffing method as defined in ISO 15848-1:2015, Annex B.2 © ISO 2015 – All rights reservedBS EN ISO 15848-2:2015ISO 15848-2:2015(E) 6.2 Measurement of leakage of body seal(s) The procedure for measuring the leakage of body seals is as follows. a) Half open the test valve and pressurize to the level specified in 5.3. After the test pressure has been stabilized, detect leakage of the body seal(s) in accordance with ISO 15848-1:2015, Annex B. b) If the reading exceeds the value of the required tightness class according to Table 2, the test shall be considered as having failed. A corrective action shall be proposed and agreed with the purchaser or the lot of valves shall be rejected. Table 2 — Leakage from body seals Measured leakage ppmv ≤50 NOTE Measured by the sniffing method as defined in ISO 15848-1:2015, Annex B. 7 Marking Only those valves which have been tested, classified, and qualified in accordance with ISO 15848-1, and which comply with the requirements of this part of ISO 15848 shall be marked. 8 Certification of compliance If requested by the purchaser, the manufacturer shall provide a certificate of compliance that this production acceptance test has been completed successfully.© ISO 2015 – All rights reserved 3This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, whe
展开阅读全文
  标准图书馆所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
0条评论

还可以输入200字符

暂无评论,赶快抢占沙发吧。

关于本文
本文标题:BS EN ISO 15848-2-2015
链接地址:http://www.stdlibrary.com/p-165005.html
关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服客服 - 联系我们

@copyright 2017-Stdlibrary All Rights Reserved.


收起
展开