欢迎来到标准图书馆! | 帮助中心 Day Day UP!
标准图书馆
首页 标准图书馆 > 资源分类 > PDF文档下载

ASTM A1002 - 10 (2015).pdf

  • 资源大小:67.72KB        全文页数:2页
  • 资源格式: PDF        下载权限:游客/注册会员/VIP会员    下载费用:20Gold 【人民币20元】
游客快捷下载 游客一键下载
会员登录下载
下载资源需要20Gold 【人民币20元】Paypal charge shall be login

邮箱/手机号:
您支付成功后,系统会自动为您创建此邮箱/手机号的账号,密码跟您输入的邮箱/手机号一致,以方便您下次登录下载和查看订单。注:支付完成后需要自己下载文件,并不会自动发送文件哦!

支付方式: 微信支付    支付宝   
验证码:   换一换

友情提示
2、本站资源不支持迅雷下载,请使用浏览器直接下载(不支持QQ浏览器)
3、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰   

ASTM A1002 - 10 (2015).pdf

Designation A1002 − 10 Reapproved 2015Standard Specification forCastings, Nickel-Aluminum Ordered Alloy1This standard is issued under the fixed designation A1002; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers nickel-aluminum ordered alloycastings intended for elevated-temperature applications such asheat-resisting alloy furnace rollers, supports, hangers, and soforth, in environments up to 2300F 1260C.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.2.1 The SI gage length for tension test specimens is inbrackets and is considered standard.2. Referenced Documents2.1 ASTM Standards2A370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA781/A781M Specification for Castings, Steel and Alloy,Common Requirements, for General Industrial Use3. General Conditions for Delivery3.1 Material furnished to this specification shall conform tothe requirements of Specification A781/A781M, including anysupplementary requirements that are indicated in the purchaseorder. Failure to comply with the general requirements ofSpecification A781/A781M constitutes nonconformance withthis specification. In case of conflict between the requirementsof this specification and Specification A781/A781M, thisspecification shall prevail.4. Ordering Information4.1 The purchaser should specify the alloy grade desiredand whether tension or impact tests are required, and shallinclude standards of acceptance where necessary.5. Materials and Manufacture5.1 ProcessThe alloy for the castings shall be by anymethod unless otherwise agreed upon between the manufac-turer and the purchaser. Casting may be poured in sand, shell,investment, or centrifugal molds.5.2 Heat TreatmentCastings may be shipped in the as-castcondition. If heat treatment is required the treatment shall beestablished by mutual consent between the manufacturer andthe purchaser and shall be so specified in the inquiry, purchaseorder, or contract.6. Chemical Composition6.1 The castings shall conform to the requirements as tochemical composition prescribed in Table 1.7. Mechanical Properties7.1 Mechanical properties are not required unless specifiedin the purchase order.7.2 Tensile properties, if required, of the alloy used for thecastings shall conform to the requirements prescribed in thepurchase order.7.3 Impact properties, if required, of the alloy used for thecastings shall conform to the requirements prescribed in thepurchase order.8. Test Specimens8.1 Test specimens, if required, shall be prepared in accor-dance with Test Methods and Definitions A370. Test bars shallbe poured in special blocks from the same heat as the castingsrepresented. Test bars, if required, shall be furnished insufficient number to furnish specimens for the tests required inSection 9.8.2 The test coupons shall be cast from the same melt fromwhich the castings they represent are poured, and shall repre-sent the full melting practice. Chemical composition of the testcoupons shall conform to the requirements prescribed in Table1.8.3 Tension test specimens shall be machined to the formand dimensions of the standard 2-in. [50-mm] gage lengthspecimen shown in Fig. 4 of Test Methods and DefinitionsA370.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.18 on Castings.Current edition approved Dec. 1, 2015. Published December 2015. Originallyapproved in 1999. Last previous edition approved in 2010 as A1002 – 10. DOI10.1520/A1002-10R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standard’s Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States18.4 Impact test specimens shall conform to the length andcross-section dimensions shown in Fig. 10 of Test Methods andDefinitions A370. The impact specimens are to be brokenunnotched.9. Number of Tests and Retests9.1 Tension TestOne tension test, if required by thepurchase order, shall be made from each heat.9.2 Impact TestOne unnotched Charpy impact test, ifrequired by the purchase order, shall be made from each heat.9.3 Retests9.3.1 Retests of a duplicate specimen will be allowed if theresults of the mechanical tests for any lot does not conform tothe requirements specified in the purchase order.9.3.2 If the elongation of any tension test specimen is lessthan specified, and any part of the fracture is more than3⁄4 in.[19.0 mm] from the center of the gage length, as indicated byscribe scratches marked on the specimen before testing, a retestshall be allowed.10. Keywords10.1 casting; elevated temperature; heat-resistant alloy;heat-resisting; nickel aluminide; nickel aluminumSUPPLEMENTARY REQUIREMENTSSupplementary requirements only apply when specified in the purchase order. A list of standardizedsupplementary requirements for use at the option of the purchaser is included in SpecificationA781/A781M. Supplementary Requirements S1 and S11 of Specification A781/A781M are notappropriate for this specification and shall not be specified. In addition, the following SupplementaryRequirement S18, for welding applications, is not listed in Specification A781/A781M.S18. Welding ApplicationsS18.1 The sulfur shall be 0.003 by weight or less and thesilicon shall be 0.05 by weight or less. Detailed informationconcerning welding is available from Materials Processing,Metals and Ceramics Div., Oak Ridge National Laboratory,P.O. Box 2008, Oak Ridge, TN 37831-6083.SUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to this standard since the last issue A1002 – 992009 that may impact the use of this standard. Approved April 1, 2010.1 Table 1, Deleted Zr requirement, Modified Al and Moupper limits.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 phone, 610-832-9555 fax, or serviceastm.org e-mail; or through the ASTM websitewww.astm.org. Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel 978 646-2600; http//www.copyright.com/TABLE 1 Chemical RequirementsElement Composition, by WeightCarbon, max 0.08Sulfur, maxA0.020Aluminum 7.3–8.5Chromium 7.5–8.5Molybdenum 1.20–1.80Boron 0.003–0.012Silicon, maxA0.20Iron, max 1.00Nickel BalanceAFor welding applications, see S18 for restrictions on sulfur and silicon.A1002 − 10 20152

注意事项

本文(ASTM A1002 - 10 (2015).pdf)为本站会员(admin)主动上传,标准图书馆仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知标准图书馆(发送邮件至[email protected]或直接QQ联系客服),我们立即给予删除!

温馨提示:如果因为网速或其他原因下载失败请重新下载,重复下载不扣分。

关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服客服 - 联系我们

@copyright 2017-Stdlibrary All Rights Reserved.


收起
展开